Concrete Floor Stripping & Removal in Pinecrest FL - a clean slab ready for a new floor

Old epoxy peeling, flaking or just worn out? We take it off down to bare concrete so your next floor has something solid to grab.

Empty two-car garage with a glossy, tan-and-gray speckled floor coating and a matching raised platform.
Service
Concrete Floor Stripping & Removal

How can you tell your old floor coating needs to come off?

  • Epoxy lifting at the edges

    You'll see the coating curl up along the walls or peel in patches where the car tires sit, and that usually means it's lost its grip on the concrete underneath. The longer it goes, the more water and grit creep under it, and nothing new will hold on top of a coat that's letting go.

  • Worn through in the traffic lanes

    Gray concrete showing in the walk paths and in front of the workbench usually means the coat has reached the end of its life. Patching over it tends to leave a floor that looks fine for a season and then fails along the same wear lines.

  • Something old showing underneath

    Where the coating's chipped, you might spot an older floor or a pattern under it, which tells you the slab has layers nobody has sorted out yet. Pulling at it yourself is the one thing I'd ask you not to do until we know what it's made of.

How do you get old epoxy off a concrete floor in Pinecrest?

Concrete floor stripping and removal takes an old epoxy coating off your slab so you're back to bare concrete, and here in Pinecrest we do it by grinding the coating off with a machine or stripping it chemically, depending on the floor.

Most calls I get start with a coating that's peeling, worn through or just not what you want anymore, and the first thing I'll want to know is whether there's older flooring on that slab too. At Fieldstone Pinecrest Concrete Coatings, the price and the schedule mostly turn on how big the floor is, which removal method suits it and what we find under the coating, and your estimate spells out the prep so you can see where the money goes. Miami-Dade County licenses the contractors who work here, and we're licensed and fully insured.

Details to note before an estimate

  • Rough size of the floor
  • Type of coating, if you know it
  • Old flooring and any labels on it
  • Number of units in the building

How our concrete floor stripping and removal works

Before we take up any coating, I want to know what else is on that slab, because old flooring can hide things you don't want in the air, and if something's in question we leave it alone rather than grind through it. Once that's clear, we choose between grinding the coating off and stripping it chemically based on the floor and your budget. Our crew protects the walls and anything staying in the room, takes the coating down to bare concrete, then cleans up the dust or residue so the slab is ready for whatever goes on it next. I'm on site with the installers through the whole job, and the work is backed by our satisfaction guarantee.

Most floors we strip are getting a new coat, so we often roll straight into epoxy floor coatings on the same clean slab. Shop and business owners taking a tired work floor back to concrete usually go on to commercial and industrial epoxy floor coatings, which are built for carts, equipment and heavier traffic.

  • Epoxy Floor Coatings

    With the old coat gone, your bare slab is ready for a fresh epoxy finish that bonds to clean concrete instead of a failing layer.

  • Commercial & Industrial Epoxy Floor Coatings

    For shops, warehouses and business floors, a heavier coating system stands up to carts, equipment and daily foot traffic once the worn layer is stripped away.

What happens when you call about stripping a floor in Pinecrest?

  1. Call or send the form

    Reach us at (786) 435-0197 or through the form, and most of the time I'm the one who calls you back. We'll find a time for me to come see the floor.

  2. I check the slab myself

    I look at the coating, what's under it and how the slab is holding up, and tell you straight what it can and can't take. You get a written estimate that spells out the prep along with the finish, so the price isn't a mystery number.

  3. We strip it and walk it

    We set a date, and our installers do the work with me on site the whole way through. Once the slab is bare and cleaned up, we walk it with you before we pack up.

Questions before you book floor stripping

What is the best way to remove an epoxy coating from a concrete floor?

For most floors, a machine method like diamond grinding or shot blasting is the most direct way to get epoxy off, though chemical stripping can be the better fit for a small area or a fragile surface under the coating. Chemical strippers give off fumes, so that route needs good ventilation and protective gear for whoever's doing the work. Tell me what's going on the floor next and I'll factor that in too.

How do I know if my old flooring contains asbestos?

You generally can't tell by looking unless the material is labeled, and the EPA's advice for homes is that when you're in doubt, you treat it as if it does contain asbestos and leave it alone. The EPA also advises against running a power stripper on flooring that might contain asbestos, and against sanding or leveling that flooring or its backing. That's why the old-flooring question comes before any talk of method.

How much does it cost to strip an epoxy floor in Pinecrest?

The cost comes down to the floor's size, the removal method and what's sitting on the slab besides the coating, and your written estimate puts a number on your floor. Machine methods usually cost more upfront, while chemical stripping tends to cost less at first but makes for a slower, more labor-intensive job. If your floor could go either way, I'll lay out both so you can pick.

How long does it take to remove epoxy from a concrete floor?

Machine removal is the quicker route, and chemical stripping takes longer because it's slower, more hands-on work. Floor size matters too, and if old flooring turns up, sorting out what it's made of comes before anything else. Once the estimate is done, we set a date with you.

Do I need a permit to strip a concrete floor in Pinecrest?

Pinecrest's permit list doesn't settle it, because it says installing floors takes a general building permit plus special system permits but doesn't name taking a floor out. So before we start, we check with the Village of Pinecrest or whichever office covers your address, since we work in Pinecrest and the cities around it across Miami-Dade County. If a permit is needed, the application is signed and notarized by you or your representative and by a registered contractor, and we handle our side and walk you through yours. Building without a required permit there can bring a $500 fine per day, so it's worth asking first.

Does my building need asbestos review from Miami-Dade County?

If it's a commercial building or one of the residential buildings the county names, such as one with five or more units, most renovation work there needs asbestos review and approval from Miami-Dade County. Florida's asbestos rules for renovations also cover every building except those that meet a residential exemption, and the owner of a covered building has to notify the state before the work starts. If you own a shop, a business space or a building with several units, tell me that up front along with what's on the slab.

Find out what's under your old coating

Call (786) 435-0197 any day of the week or use the form, and I'll come look at the floor before anyone puts a tool to it.